Tire size calculator
Compare two tire sizes side by side: overall diameter, width, sidewall height, circumference and revolutions per mile, plus how your speedometer reading changes. Type sizes in any common format.
225/50R18 compared with 285/35ZR19
The new size (285/35ZR19) is 0.01% shorter than the current size (225/50R18): about 0.0 in (0 mm) less overall diameter.
It is 60 mm wider, with a sidewall 13 mm shorter.
The current size is made for a 18-inch wheel and the new size for a 19-inch wheel, so changing between them means different wheels.
| Measurement | Current (225/50R18) | New (285/35ZR19) | Difference (new minus current) |
|---|---|---|---|
| Overall diameter | 26.9 in (682 mm) | 26.9 in (682 mm) | 0.0 in (0 mm), -0.01% |
| Section width | 8.9 in (225 mm) | 11.2 in (285 mm) | +2.4 in (+60 mm) |
| Sidewall height | 4.4 in (113 mm) | 3.9 in (100 mm) | -0.5 in (-13 mm) |
| Circumference | 84.4 in (2143 mm) | 84.4 in (2143 mm) | 0.0 in (0 mm) |
| Revolutions per mile | 751 | 751 | 0 |
These are nominal design dimensions. Real tires vary by brand, tread depth, wheel width, load and pressure.
Is the difference small?
The overall diameter differs by 0.01%, which is within the common 3% rule of thumb.
The rule of thumb keeps a replacement size within about 3% of the original overall diameter. It covers diameter only. It is not a fit, load or safety check, because width, wheel diameter, load capacity and clearance matter too. Confirm any size change with your vehicle's owner's manual or a tire professional.
Speedometer difference
A shorter tire covers less ground on every turn, but the speedometer counts turns as if the tire were still the original size. With the new size the speedometer reads high: when it shows 60 mph, your actual speed is about 60.0 mph. These figures assume the speedometer is accurate on the current size and use nominal tire dimensions, so treat them as estimates.
| Speedometer shows | Actual speed | Difference |
|---|---|---|
| 20 mph | 20.0 mph | 0.0 mph |
| 30 mph | 30.0 mph | 0.0 mph |
| 40 mph | 40.0 mph | 0.0 mph |
| 50 mph | 50.0 mph | 0.0 mph |
| 60 mph | 60.0 mph | 0.0 mph |
| 70 mph | 70.0 mph | 0.0 mph |
| 80 mph | 80.0 mph | 0.0 mph |
What this calculator compares
Enter your current tire size and a size you are thinking about, and the calculator puts them side by side. It reads the section width, aspect ratio and wheel diameter from each size and works out the measurements that decide whether one tire can stand in for the other: section width, sidewall height, overall diameter, circumference and revolutions per mile. It then shows what the change does to your speedometer and odometer.
Sizes can be typed in any common format, such as 225/65R17, P225/65R17 or 225 65 R17, and flotation sizes like 33x12.50R15 work too. If you are not sure what the numbers mean, the guide to reading a tire sidewall explains each one.
How the measurements are worked out
The sidewall is the tire's width times its aspect ratio, so a 225/65R17 has a sidewall that is 65 percent of 225 mm, about 146 mm (5.8 in). The overall diameter is the wheel diameter plus two sidewalls, one above the wheel and one below. The circumference is pi times the overall diameter, and revolutions per mile is the 63,360 inches in a mile divided by that circumference.
For example, 225/65R17 is 28.5 in tall overall and turns about 707 times per mile. 235/65R17 is 29.0 in tall and turns about 695 times per mile, so it is 1.79% taller. These are nominal design dimensions. Real tires vary by brand, tread depth, wheel width, load and pressure.
The speedometer works from the same count. It measures how fast the wheels turn and assumes each turn covers the distance of the original tire. A taller tire covers more ground per turn, so the speedometer reads low, and a shorter tire reads high. The size of the error is the same percentage as the difference in overall diameter, and the odometer is off by the same amount. For speeds at each speedometer reading, use the speedometer error calculator.
When is a different tire size close enough?
A common general guideline is to keep a replacement tire's overall diameter within about ±3% of the original. That keeps the speedometer error, the gearing and the vehicle's ride height close to what the maker designed. It is a rule of thumb, not a law and not a safety check, and some vehicle makers allow less.
The guideline covers diameter only. It does not tell you whether the new tire clears the suspension and wheel well, whether the wheel is the right width for it, or whether its load index and speed rating are high enough for your vehicle. The guide to plus sizing wheels and tires walks through those checks. Confirm any size change with your vehicle's owner's manual or a tire professional.